Skip Navigation

Westland Select Fit Boat Covers

Measuring Your Boat and Knowing Your Motor Type

Boat measurement and motor type identification diagram.

Westland Select Fit Boat Covers are applied by the general hull style and basic dimensions of the boat being covered. These covers are listed in 1’ increments on the half-foot, so the cover may fit a little tighter or looser, depending on the centerline length and beam width of your boat, in comparison to the listed dimensions for the cover. Each cover has a draw rope sewn into the hem of the cover for purposes of pulling the cover tight and tie down loops sewn throughout for tying the cover down.

These covers are available in 4 material options: Sunbrella with a 10 year warranty, Sharkskin Supreme SD with a 7 year warranty, Sharkskin Plus with a 5 year warranty. All of Westland’s covers are reinforced at high stress areas and have two sewn in vent caps to increase breathability.

To ensure you choose the correct cover: First, select the style that most resembles your boat. Of course, check the console dimensions, rail allowance, and trolling motor (or any other added feature) accommodations as well. Next, to obtain the centerline length of the boat, simply run a measuring tape down the side or center of your boat from the furthest point of the bow (be sure you do not contour to any curves or go up and over anything like a windshield or console) to the back of the transom. Lastly, the beam is a measurement taken from gunnel to gunnel at the widest point, also in a straight line without contour.

Select Your Sub-Style, Motor Configuration and Dimensions

aluminum-fishing-boat Illustration

Aluminum Fishing Boat Covers

Designed for aluminum V-hull style fishing boats. Covers are large enough to accommodate folded or low fishing seats and center or side consoles. Trolling motors can sometimes be accommodated with this cover as well.

1
2
aluminum-jet-boat Illustration

Aluminum Jet Boat Covers

Designed to fit V-Hull aluminum jet sled boats with forward mounted windshields typically used in the Northwest United States where shallow river fishing is prominent. Covers can be used in applications where a side or center console are on the boat instead of the windshield.

1
2
aluminum-jon-boat Illustration

Aluminum Jon Boat Covers

Designed for aluminum jon boat style boats with squared off front bow. Covers are large enough to support folded or low profile fishing seats and low profile center and side consoles.

1
2
v-shaped-jon-boat Illustration

V-Shaped Jon Boat Covers

Designed to accommodate aluminum Jon Boat style boats with flared front bow and side consoles without plexi windshields. Covers are large enough to cover folded or low profile fishing seats and will accommodate a port trolling motor.

1
2
v-shaped-jon-boat-with-center-console Illustration

V-Shaped Jon Boat With Center Console Covers

Designed to accommodate aluminum Jon Boat style boats with flared front bow and medium to high center consoles up to 30" from the deck to the center console windshield. Covers are large enough to cover folded or low profile fishing seats and will accommodate a port trolling motor.

1
2
bay-fisherman Illustration

Bay Fisherman Covers

Designed to fit low and medium profile center console in-shore shallow draft fishing boats with square or flared v-shaped bows. Boats are generally made out of either aluminum or fiberglass. Cover will accommodate a console height up to 60" from the floor and bow rails up to 6" in height.

1
2
center-console-with-bow-rails Illustration

Center Console With Bow Rails Covers

Consoles are accommodated at heights of 30" from the gunnel to top of center console windshield. Bow rails should be no higher than 15". For boats with bow pulpits, add the length of pulpit to centerline length.

1
2
center-console-without-bow-rails Illustration

Center Console Without Bow Rails Covers

Consoles are accommodated at heights of 30" from the gunnel to the center console windshield, but there should not be bow rails. For boats with bow pulpits, add the length of pulpit to centerline length.

1
2
conventional-bass-boat Illustration

Conventional Bass Boat Covers

Fits fishing boats with squared or flared bows, tri-hull bass boats or modified bass boats. Covers are large enough to accommodate folded or low profile fishing trolling motors, windscreens and single or dual console models.

1
2
conventional-tournament-ski-boat Illustration

Conventional Tournament Ski Boat Covers

Designed for closed bow conventional tournament style ski boats with non-integrated swim platforms, squared windshields and a pointed bow. Does not accommodate wakeboard towers. Fits boats with I/O stern drive or direct drive.

1
2
conventional-tournament-ski-boat-with-tower Illustration

Conventional Tournament Ski Boat With Tower Covers

Designed for open bow conventional tournament style ski boats with squared windshield, pointed bow, non-integrated swim platforms and mid ship deck mounted wakeboard towers. Uses 48" cutouts with hook and loop fasteners to seal around tower legs and still keep out water. Fits boats with I/O stern drive or direct drive.

1
2
tournament-ski-boat-with-sport-arch Illustration

Tournament Ski Boat With Sport Arch Covers

Desigined for conventional style ski boats with mid ship top mount arch style sports tower. Uses single 52" cutout per side with hook loop fastners to seal around tower legs. Fits i/o stern drive and direct drive boats.

1
2
conventional-v-hull-cuddy Illustration

Conventional V-Hull Cuddy Covers

Fits low to medium profile cuddy cabin boats with bow rails up to 20" and squared glass windshields. When ordering for boats with bow pulpits, add length of pulpit to centerline length.

1
2
conventional-v-hull-runabout Illustration

Conventional V-Hull Runabout Covers

Fits open and closed bow style runabouts and low profile cuddy style boats. Accommodates bow rails up to 10" in height and squared glass windshields. I/O and O/B versions.

1
2
deck-boat Illustration

Deck Boat Covers

Designed for deck style boats. Covers will accommodate consoles with or without windshields or windscreens. Covers extended platform. I/O

1
2
drift-boat Illustration

Drift Boat Covers

Designed to accommodate aluminum or wooden drift boats. Large enough to accommodate folded or low profile seats. No bow bra. Only non-trailerable covers available.

1
2
euro-cruiser Illustration

Euro Cruiser Covers

Fits high profile cabin cruisers with euro style integrated swim platforms. Overall centerline listed includes swim platform. When ordering for boats with bow pulpits, add the length of the pulpit to centerline length. Accommodates bow rails up to 30"and curved glass windshields. Cover does not accommodate radar arches. I/O

1
2
euro-cuddy Illustration

Euro Cuddy Covers

Fits cuddy cabin boats with euro style integrated swim platforms and curved windshields. Overall centerline listed includes swim platform. When ordering for boats with bow pulpits, add the length of the pulpit to centerline length. Accommodates bow rails up to 20". I/O

1
2
euro-tournament-ski-boat Illustration

Euro Tournament Ski Boat Covers

Euro style tournament or competition ski boats featuring molded or integrated swim platforms. Overall centerline length includes swim platform. Does not accommodate a wakeboard tower.

1
2
euro-tournament-ski-boat-with-wakeboard-tower Illustration

Euro Tournament Ski Boat With Wakeboard Tower Covers

Designed for euro style tournament or competition ski boats featuring molded or integrated swim platforms and a mid-ship deck mounted wakeboard tower. Uses 48" cutouts with hook and loop fasteners to seal around tower legs and still keep out water. Overall centerline length includes swim platform.

1
2
euro-v-hull-runabouts Illustration

Euro V-Hull Runabouts Covers

Fits open and closed bow style runabouts and low profile cuddy style boats with euro style integrated swim platforms and curved glass windshields. Overall centerline length listed includes swim platform. Accommodates bow rails up to 3" in height. Inboard and outboard versions.

1
2
euro-v-hull-runabouts-with-wakeboard-tower Illustration

Euro V-Hull Runabouts With Wakeboard Tower Covers

Fits open and closed bow style runabouts and low profile cuddy style boats with euro style integrated swim platforms and curved glass windshields. Designed for boats with a mid-ship deck mounted wakeboard tower. Overall centerline length listed includes swim platform. Accommodates bow rails up to 3" in height.

1
2
fiberglass-dinghy Illustration

Fiberglass Dinghy Covers

A specially designed cover to accommodate fiberglass multi-hull dinghy style boats with squared bows. O/B with no motorhood. Only non-trailerable covers available.

1
2
fish-n-ski-fishing-v-hulls-with-bow-troll-motor Illustration

Fish 'N Ski (Fishing V-Hulls With Bow Troll Motor) Covers

Fits open and closed bow Fish N' Ski style runabout and low profile cuddy style boats with bow mounted trolling motor. Inboard and outoard versions.

1
2
flat-bottom-boats Illustration

Flat Bottom Boats Covers

V-Hull flats boats with center consoles up to 30" from the top of the deck. Accommodates mounted trolling motors and aft poling platforms up to 40".

1
2
inflatable-blunt-nose Illustration

Inflatable Blunt Nose Covers

Designed for inflatable boats with a blunt nose bow with or without small outboard motor installed in tilt position. Only non-trailerable covers available.

1
2
inflatable-sport-boat Illustration

Inflatable Sport Boat Covers

Designed for inflatable boats with a blunt nose bow with or without small outboard motor installed in tilt position. Only non-trailerable covers available.

1
2
jet-sport-boat Illustration

Jet Sport Boat Covers

Designed to accommodate the popular 13' to 23' jet style boats.

1
2
low-profile-ski-boat Illustration

Low Profile Ski Boat Covers

For low profile ski/sport boats. Accommodate boats with or without windshields or windscreens and with or without bow rails. I/O version fits boats with I/O stern drives, jets, or bracket mounted outboards. Inboard and outboard version.

1
2
offshore-day-cruiser Illustration

Offshore Day Cruiser Covers

Designed for low profile offshore and day cruiser style sport boats. Covers will accommodate boats with or without windshields. Available for 96" or 102" wide models. Fits boats with I/O stern drives, jets, or bracket mounted outboards.

1
2
pontoon-boat Illustration

Pontoon Boat Covers

For pontoon boats when the bimini top or hard top is folded down. Covers will accommodate boats with or without windshields or windscreens. Accommodates outboard or I/O stern drive models. Only non-trailerable covers available.

1
2
pro-bass-boats Illustration

Pro Bass Boats Covers

V-hull or semi-V style bass boats with single or twin consoles. Large enough to accommodate fishing seats, trolling motors, windscreens or windshields, etc.

1
2
tri-hull Illustration

Tri-Hull Covers

Tri-hulls or similar style with wide bows. Inboard and outboard versions.

1
2
v-hull-cruiser Illustration

V-Hull Cruiser Covers

Fits high profile cabin cruisers. Accommodates bow rails up to 30" and squared glass windshields. Cover does not accommodate radar arches. Add on the length of the bow pulpit when measuring the centerline of the boat. I/O but can accommodate O/B models with deep inset wells.

1
2
whaler Illustration

Whaler Covers

Designed for smaller center consoles, side consoles, or "tender" style boats with bow rails up to 18".

1
2
v-hull-sport-arch Illustration

V-Hull Sport Arch Covers

Fits open and closed bow style runabouts and low profile cuddy style boats. Accommodates bow rails up to 10" in heights and squared glass windshields with Sport Arch tower. Uses one 48" cutout with hook and loop fastener to seal around tower legs in each side.

1
2