Skip Navigation

Fishing Boats Style Boat Covers

Measuring Your Boat and Knowing Your Motor Type

Boat measurement and motor type identification diagram.

Westland Select Fit Boat Covers are applied by the general hull style and basic dimensions of the boat being covered. These covers are listed in 1’ increments on the half-foot, so the cover may fit a little tighter or looser, depending on the centerline length and beam width of your boat, in comparison to the listed dimensions for the cover. Each cover has a draw rope sewn into the hem of the cover for purposes of pulling the cover tight and tie down loops sewn throughout for tying the cover down.

These covers are available in 4 material options: Sunbrella with a 10 year warranty, Sharkskin Supreme SD with a 7 year warranty, Sharkskin Plus with a 5 year warranty. All of Westland’s covers are reinforced at high stress areas and have two sewn in vent caps to increase breathability.

To ensure you choose the correct cover: First, select the style that most resembles your boat. Of course, check the console dimensions, rail allowance, and trolling motor (or any other added feature) accommodations as well. Next, to obtain the centerline length of the boat, simply run a measuring tape down the side or center of your boat from the furthest point of the bow (be sure you do not contour to any curves or go up and over anything like a windshield or console) to the back of the transom. Lastly, the beam is a measurement taken from gunnel to gunnel at the widest point, also in a straight line without contour.

Select Your Sub-Style, Motor Configuration and Dimensions

aluminum-fishing-boat Illustration

Aluminum Fishing Boat Covers

Designed for aluminum V-hull style fishing boats. Covers are large enough to accommodate folded or low fishing seats and center or side consoles. Trolling motors can sometimes be accommodated with this cover as well.

1
2
aluminum-jet-boat Illustration

Aluminum Jet Boat Covers

Designed to fit V-Hull aluminum jet sled boats with forward mounted windshields typically used in the Northwest United States where shallow river fishing is prominent. Covers can be used in applications where a side or center console are on the boat instead of the windshield.

1
2
aluminum-jon-boat Illustration

Aluminum Jon Boat Covers

Designed for aluminum jon boat style boats with squared off front bow. Covers are large enough to support folded or low profile fishing seats and low profile center and side consoles.

1
2
v-shaped-jon-boat Illustration

V-Shaped Jon Boat Covers

Designed to accommodate aluminum Jon Boat style boats with flared front bow and side consoles without plexi windshields. Covers are large enough to cover folded or low profile fishing seats and will accommodate a port trolling motor.

1
2
conventional-bass-boat Illustration

Conventional Bass Boat Covers

Fits fishing boats with squared or flared bows, tri-hull bass boats or modified bass boats. Covers are large enough to accommodate folded or low profile fishing trolling motors, windscreens and single or dual console models.

1
2
drift-boat Illustration

Drift Boat Covers

Designed to accommodate aluminum or wooden drift boats. Large enough to accommodate folded or low profile seats. No bow bra. Only non-trailerable covers available.

1
2
fish-n-ski-fishing-v-hulls-with-bow-troll-motor Illustration

Fish 'N Ski (Fishing V-Hulls With Bow Troll Motor) Covers

Fits open and closed bow Fish N' Ski style runabout and low profile cuddy style boats with bow mounted trolling motor. Inboard and outoard versions.

1
2
pro-bass-boats Illustration

Pro Bass Boats Covers

V-hull or semi-V style bass boats with single or twin consoles. Large enough to accommodate fishing seats, trolling motors, windscreens or windshields, etc.

1
2
v-shaped-jon-boat-with-center-console Illustration

V-Shaped Jon Boat With Center Console Covers

Designed to accommodate aluminum Jon Boat style boats with flared front bow and medium to high center consoles up to 30" from the deck to the center console windshield. Covers are large enough to cover folded or low profile fishing seats and will accommodate a port trolling motor.

1
2
whaler Illustration

Whaler Covers

Designed for smaller center consoles, side consoles, or "tender" style boats with bow rails up to 18".

1
2
flat-bottom-boats Illustration

Flat Bottom Boats Covers

V-Hull flats boats with center consoles up to 30" from the top of the deck. Accommodates mounted trolling motors and aft poling platforms up to 40".

1
2
center-console-without-bow-rails Illustration

Center Console Without Bow Rails Covers

Consoles are accommodated at heights of 30" from the gunnel to the center console windshield, but there should not be bow rails. For boats with bow pulpits, add the length of pulpit to centerline length.

1
2
center-console-with-bow-rails Illustration

Center Console With Bow Rails Covers

Consoles are accommodated at heights of 30" from the gunnel to top of center console windshield. Bow rails should be no higher than 15". For boats with bow pulpits, add the length of pulpit to centerline length.

1
2
bay-fisherman Illustration

Bay Fisherman Covers

Designed to fit low and medium profile center console in-shore shallow draft fishing boats with square or flared v-shaped bows. Boats are generally made out of either aluminum or fiberglass. Cover will accommodate a console height up to 60" from the floor and bow rails up to 6" in height.

1
2